mimix broadbands 18.0-50.0 ghz gaas mmic distributed amplifier has a small signal gain of 17.0 db with a noise figure of 5.0 db across the band. the device also includes 30.0 db gain control and a +15 dbm p1db compression point. this mmic uses mimix broadbands gaas phemt device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. the chip has surface passivation to protect and provide a rugged part with backside via holes and gold metallization to allow either a conductive epoxy or eutectic solder die attach process. this device is well suited for microwave, millimeter-wave and wideband military applications. 18.0-50.0 ghz gaas mmic distributed amplifier january 2010 - rev 11-jan-10 absolute maximum ratings page 1 of 8 features ultra wide band driver amplifier fiber optic modulator driver 17.0 db small signal gain 5.0 db noise figure 30 db gain control +15.0 dbm p1db compression point 100% on-wafer rf, dc and output power testing 100% visual inspection to mil-std-883 method 2010 general description supply voltage (vd) supply current (id) gate bias voltage (vg) input power (pin) storage temperature (tstg) operating temperature (ta) channel temperature (tch) 1 +6.0 vdc 220 ma +0.3 vdc +15 dbm -65 to +165 oc -55 to +85 oc +175 oc chip device layout (1) channel temperature affects a device's mttf. it is recommended to keep channel temperature as low as possible for maximum life. frequency range (f ) input return loss (s11) 2 output return loss (s22) 2 small signal gain (s21) 2 gain flatness ( s21) gain control reverse isolation (s12) 2 noise figure (nf) output power for 1 db compression (p1db) output third order intercept point (oip3) drain bias voltage (vd) gain control bias (vg) supply current (id) (vd=5.0v, vg=0.0 typical) electrical characteristics (ambient temperature t = 25 o c) parameter units ghz db db db db db db db dbm dbm vdc vdc ma min. 18.0 5.0 6.0 13.0 - - 30.0 - - - - -2.0 - typ. - 10.0 11.0 17.0 +/-1.0 30.0 40.0 5.0 +15.0 +24.0 +5.0 0.0 160 max. 50.0 - - - - - - - - - +5.5 +0.1 190 (1) measured using constant current. (2) unless otherwise indicated min/max over 18.0-50.0 ghz and biased at vd=5v, id=160 ma 1 1 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. d1001-bd
distributed amplifier measurements (on-wafer 1 ) page 2 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. note [1] measurements C on-wafer data has been taken using bias conditions as shown. measurements are referenced 150 um in from rf in/out pad edge. for optimum performance mimix t-pad transition is recommended. for additional information see the mimix t-pad transition application note. xd1001-bd, vd=5.0 v, id=150 ma (4631 devices) 1 8 1 9 2 0 2 1 2 2 1 2 1 3 1 4 1 5 1 6 1 7 18 . 0 2 0 . 0 22 . 0 24 . 0 26 . 0 28 . 0 30 . 0 32 . 0 3 4 . 0 36 . 0 38 . 0 40 . 0 42 . 0 4 4 . 0 46 . 0 48 . 0 50 . 0 frequency (ghz) gain (db) m a x m ed i a n m ea n - 3 s i g m a xd1001-bd, vd=5.0 v, id=150 ma (5039 devices) - 3 0 - 2 0 - 1 0 0 - 7 0 - 6 0 - 5 0 - 4 0 18 . 0 20 . 0 22 . 0 24 . 0 26 . 0 28 . 0 3 0 . 0 32 . 0 34 . 0 3 6 . 0 38 . 0 40 . 0 42 . 0 44 . 0 46 . 0 4 8 . 0 50 . 0 frequency (ghz) reverse isolation (db) m a x m e d i a n m ea n - 3 s i g m a xd1001-bd, vd=5.0 v, id=150 ma (4786 devices) - 1 0 - 5 0 - 2 5 - 2 0 - 1 5 1 8 . 0 20 . 0 22 . 0 24 . 0 2 6 . 0 28 . 0 3 0 . 0 3 2 . 0 34 . 0 36 . 0 38 . 0 40 . 0 42 . 0 4 4 . 0 46 . 0 4 8 . 0 50 . 0 frequency (ghz) input return loss (db) m a x m ed i a n m e a n - 3 s i g m a g xd1001-bd, vd=5.0 v, id=150 ma (4751 devices) - 2 0 - 1 5 - 1 0 - 5 0 - 4 5 - 4 0 - 3 5 - 3 0 - 2 5 18 . 0 2 0 . 0 22 . 0 24 . 0 26 . 0 28 . 0 3 0 . 0 32 . 0 34 . 0 3 6 . 0 38 . 0 40 . 0 4 2 . 0 44 . 0 46 . 0 48 . 0 50 . 0 frequency (ghz) output retrun loss (db) m a x m e d i a n m ea n - 3 s i g m a g xd1001-bd, vd=5.0 v, id=150 ma (~35 devices) 1 4 1 5 1 6 1 7 1 8 1 9 2 0 1 0 1 1 1 2 1 3 1 4 18 . 0 20 . 0 22 . 0 24 . 0 26 . 0 28 . 0 30 . 0 32 . 0 34 . 0 3 6 . 0 38 . 0 40 . 0 42 . 0 44 . 0 46 . 0 48 . 0 50 . 0 frequency (ghz) output power p1db (dbm) m a x m ed i a n m ea n - 3 s i g m a xd1001-bd, vd=5.0 v, id=150 ma (~35 devices) 5 . 0 5 . 5 6 . 0 6 . 5 7 . 0 3 . 0 3 . 5 4 . 0 4 . 5 1 8 . 0 1 9 . 0 20 . 0 21 . 0 22 . 0 23 . 0 2 4 . 0 25 . 0 26 . 0 27 . 0 28 . 0 29 . 0 3 0 . 0 frequency (ghz) noise figure (db) m a x m e d i a n m ea n m i n
page 3 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. distributed amplifier measurements (on-wafer 1 ) (cont.) note [1] measurements C on-wafer data has been taken using bias conditions as shown. measurements are referenced 150 um in from rf in/out pad edge. for optimum performance mimix t-pad transition is recommended. for additional information see the mimix t-pad transition application note. xd1001-bd, vd=5.0 v, id=various 0 2 4 6 8 1 0 1 2 1 4 1 6 1 8 2 0 - 2 0 - 1 8 - 1 6 - 1 4 - 1 2 - 1 0 - 8 - 6 - 4 - 2 0 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 1 0 0 1 1 0 1 2 0 1 3 0 1 4 0 1 5 0 drain current, id (ma) gain (db) 3 6 g h z 4 1 g h z xd1001-bd, vd=5.0 v, id=various 2 4 6 8 1 0 1 2 1 4 1 6 1 8 2 0 - 2 0 - 1 8 - 1 6 - 1 4 - 1 2 - 1 0 - 8 - 6 - 4 - 2 0 - 2 - 1 . 8 - 1 . 6 - 1 . 4 - 1 . 2 - 1 - 0 . 8 - 0 . 6 - 0 . 4 - 0 . 2 0 0 . 2 gate voltage, vg (v) gain (db) 3 6 g h z 4 1 g h z xd1001-bd, vd=3.0 v, id=various 4 . 5 5 . 0 5 . 5 6 . 0 6 . 5 7 . 0 2 . 0 2 . 5 3 . 0 3 . 5 4 . 0 2 0 . 0 2 2 . 0 2 4 . 0 2 6 . 0 2 8 . 0 3 0 . 0 3 2 . 0 34 . 0 3 6 . 0 3 8 . 0 4 0 . 0 frequency (ghz) noise figure (db) v g = 0 v v g = - 0 . 1 v v g = - 0 . 2 v v g = - 0 . 3 v v g = - 0 . 4 v g g g g g xd1001-bd, vd=various, id=150 ma 4 . 5 5 . 0 5 . 5 6 . 0 6 . 5 7 . 0 2 . 0 2 . 5 3 . 0 3 . 5 4 . 0 20 . 0 22 . 0 2 4 . 0 26 . 0 28 . 0 30 . 0 32 . 0 3 4 . 0 3 6 . 0 38 . 0 4 0 . 0 frequency (ghz) noise figure (db) v d = 3 . 0 v v d = 4 . 0 v v d = 5 . 0 v xd1001-bd, vd=5.0 v, id=various, pin=-15 dbm/tone 2 3 2 4 2 5 2 6 2 7 1 9 2 0 2 1 2 2 20 . 0 2 2 . 0 2 4 . 0 2 6 . 0 28 . 0 3 0 . 0 3 2 . 0 3 4 . 0 36 . 0 frequency (ghz) output third order intercept (dbm) v g = 0 v v g = - 0 . 1 v v g = - 0 . 2 v v g = - 0 . 3 v
page 4 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. s-parameters (on-wafer 1 ) note [1] s-parameters C on-wafer s-parameters have been taken using bias conditions as shown. measurements are referenced 150 um in from rf in/out pad edge. t y p c ial s - parame t e r da t a f o r xd1001 - b d v d =5.0 v, i d =149 m a f re qu e n c y s 1 1 s1 1 s 2 1 s2 1 s 1 2 s1 2 s 2 2 s2 2 (g h z ) ( m a g ) ( a ng ) ( m a g ) ( a ng ) ( m a g ) ( a ng ) ( m a g ) ( a ng ) 1 4 0 0 33 9 1 0 5 9 5 4 48 4 6 4 4 4 0 002 4 15 1 7 1 0 56 6 4 2 4 3 1 4 . 0 0 . 33 9 - 1 0 5 . 9 5 4 . 48 4 - 6 4 . 4 4 0 . 002 4 15 1 . 7 1 0 . 56 6 4 2 . 4 3 15. 0 0 .31 8 - 1 09.4 2 4.95 9 - 81.2 5 0.002 9 146.0 8 0.53 6 29.7 1 16. 0 0 .29 6 - 1 13.5 9 5.45 4 - 98.2 8 0.003 6 142.1 3 0.50 4 16.9 2 17. 0 0 .27 7 - 1 18.0 9 5.95 7 - 115.3 7 0.004 3 129.0 3 0.46 9 3.7 0 18. 0 0 .26 3 - 1 22.9 8 6.45 2 - 132.7 0 0.005 0 119.0 5 0.42 7 - 9 .9 8 19. 0 0 .24 8 - 1 28.1 3 6.88 6 - 150.6 1 0.005 6 106.7 9 0.37 9 - 24.2 0 20. 0 0 .22 7 - 1 30.9 1 7.22 1 - 168.6 3 0.006 5 94.1 6 0.32 5 - 38.3 9 21. 0 0 .21 9 - 1 33.0 8 7.50 2 173.6 2 0.006 8 78.9 4 0.27 1 - 53.1 2 22. 0 0 .21 8 - 1 36.8 0 7.62 7 155.9 6 0.007 3 65.4 1 0.21 8 - 66.8 2 23. 0 0 .22 2 - 1 39.9 1 7.67 2 138.7 8 0.007 7 50.1 4 0.17 0 - 79.2 6 24. 0 0 .22 5 - 1 43.3 4 7.65 6 122.1 9 0.007 5 37.5 2 0.12 9 - 89.3 8 25. 0 0 .23 3 - 1 50.1 8 7.59 6 106.1 1 0.007 9 18.7 8 0.09 6 - 98.4 5 26. 0 0 .24 2 - 1 57.6 5 7.51 9 90.7 1 0.007 4 5.4 9 0.07 0 - 103.9 2 27. 0 0 .25 0 - 1 64.4 1 7.46 5 75.6 2 0.007 8 - 6 .8 3 0 .05 9 - 103.1 9 28. 0 0 .24 9 - 1 72.2 9 7.40 4 60.8 4 0.007 8 - 24.5 8 0.05 5 - 99.3 6 29. 0 0 .24 8 - 1 78.2 5 7.39 4 46.5 8 0.007 7 - 41.5 1 0.06 0 - 99.5 4 30. 0 0 .24 9 1 7 7.0 8 7.44 5 32.0 2 0.007 1 - 55.5 7 0.08 3 - 106.6 8 31. 0 0 .25 2 1 7 1.4 0 7.50 7 17.2 3 0.007 3 - 69.6 6 0.10 8 - 120.0 7 32. 0 0 .25 2 1 6 8.8 6 7.60 6 2.0 6 0.007 5 - 85.0 7 0.14 1 - 130.9 5 33. 0 0 .25 1 1 6 9.1 2 7.69 5 - 13.8 7 0.007 9 - 104.6 7 0.17 8 - 143.9 0 34. 0 0 .26 8 1 6 5.0 8 7.70 4 - 29.8 6 0.007 5 - 121.7 4 0.21 1 - 159.2 7 35. 0 0 .29 1 1 6 1.3 5 7.65 5 - 45.9 3 0.007 9 - 135.0 9 0.24 3 - 172.4 0 36. 0 0 .30 7 1 5 9.4 8 7.54 2 - 62.2 6 0.007 9 - 152.3 2 0.27 5 174.7 0 3 7 0 0 33 1 1 5 6 2 8 7 42 3 7 8 7 7 0 008 8 16 5 7 5 0 30 5 16 3 3 6 3 7 . 0 0 . 33 1 1 5 6 . 2 8 7 . 42 3 - 7 8 . 7 7 0 . 008 8 - 16 5 . 7 5 0 . 30 5 16 3 . 3 6 38. 0 0 .37 0 1 5 0.0 2 7.16 8 - 94.5 0 0.008 3 172.5 1 0.33 4 151.7 4 39. 0 0 .38 4 1 4 4.9 2 6.98 3 - 109.6 5 0.009 0 160.6 0 0.35 1 139.4 2 40. 0 0 .38 0 1 3 9.7 0 6.92 0 - 125.0 6 0.008 0 145.4 1 0.35 2 129.5 3 41. 0 0 .39 0 1 3 6.3 5 6.82 7 - 140.8 4 0.008 7 134.3 3 0.35 2 121.5 1 42. 0 0 .39 9 1 3 2.6 8 6.82 7 - 156.3 6 0.009 0 119.7 0 0.34 5 112.7 0 43. 0 0 .40 7 1 2 8.8 9 6.92 9 - 172.6 4 0.009 1 106.2 5 0.33 1 106.1 9 44. 0 0 .41 7 1 2 6.1 0 7.01 9 169.6 4 0.009 3 91.5 0 0.32 5 100.8 5 45. 0 0 .40 7 1 2 4.1 3 6.99 2 150.3 4 0.009 4 78.2 6 0.31 3 94.9 6 46. 0 0 .40 2 1 2 4.7 4 6.88 4 131.0 8 0.009 7 58.7 0 0.30 2 93.6 6 47. 0 0 .43 6 1 2 2.8 9 6.79 4 112.5 3 0.009 9 33.8 5 0.30 6 88.7 9 48. 0 0 .43 8 1 2 1.5 4 6.69 6 92.4 6 0.009 5 21.1 8 0.28 5 82.6 9 49. 0 0 .42 6 1 1 8.5 1 6.66 2 70.9 6 0.009 8 - 2 .1 7 0 .27 8 78.0 4 50. 0 0 .41 2 1 1 4.7 8 7.00 2 45.7 2 0.010 1 - 25.7 5 0.25 8 68.4 0
page 5 of 8 mechanical drawing bond pad #1 (rf in) bond pad #2 (vd) bond pad #3 (rf out) bond pad #4 (vg) bias arrangement bypass capacitors - see app note [2] (note: engineering designator is 30da0445) units: millimeters (inches) bond pad dimensions are shown to center of bond pad. thickness: 0.110 +/- 0.010 (0.0043 +/- 0.0004), backside is ground, bond pad/backside metallization: gold all dc bond pads are 0.100 x 0.100 (0.004 x 0.004). all rf bond pads are 0.100 x 0.200 (0.004 x 0.008) bond pad centers are approximately 0.109 (0.004) from the edge of the chip. dicing tolerance: +/- 0.005 (+/- 0.0002). approximate weight: 1.572 mg. 1 2 3 4 1.300 (0.051) 0.396 (0.016) 0.922 (0.036) 1.950 (0.077) 0.0 0.0 0.379 (0.015) 1.555 (0.061) 1 2 3 4 vd rf in rf out vg rf out vg rf in vd 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd xd1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws.
page 6 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. app note [1] biasing - as shown in the bonding diagram, this device is operated with a single drain and a gain control voltage. maximum gain bias is nominally vd=5.0v, vg=0v, id=160ma. gain can be adjusted by changing vg. it is recommended to use active biasing to keep the currents constant as the rf power and temperature vary; this gives the most reproducible results. depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. the gate of the phemt is controlled to maintain correct drain current and thus drain voltage. the typical gate voltage needed to do this is 0.0v. typically the gate is protected with silicon diodes to limit the applied voltage. also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. app note [2] bias arrangement - each dc pad (vd and vg) needs to have dc bypass capacitance (~100-200 pf) as close to the device as possible. additional dc bypass capacitance (~0.01 uf) is also recommended.
page 7 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. mttf graphs these numbers were calculated based upon accelerated life test information received from the fabricating foundry and extensive thermal modeling/ finite element analysis done at mimix broadband. the values shown here are only to be used as a guideline against the end application requirements and only represent reliability information under one bias condition. ultimately bias conditions and resulting power dissipation along with the practical aspects, i.e. thermal material stack-up, attach method of device placement are the key parts in determining overall reliability for a specific application, see previous pages. if the data shown below does not meet your reliability requirements or if the bias conditions are not within your operating limits please contact technical sales for additional information. xd1001-bd vd=5.0 v, id=160 ma 1 . 0 e + 0 6 1 . 0 e + 0 7 1 . 0 e + 0 8 1 . 0 e + 0 9 mttf (hours) 1 . 0 e + 0 4 1 . 0 e + 0 5 5 5 6 5 7 5 8 5 9 5 10 5 1 1 5 12 5 backplate temperature (deg c) xd1001-bd vd=5.0 v, id=160 ma 1 . 00 e + 0 2 1 . 00 e + 0 3 1 . 00 e + 0 4 1 . 00 e + 0 5 fits 1 . 00 e + 0 0 1 . 00 e + 0 1 5 5 6 5 7 5 8 5 9 5 1 0 5 1 1 5 1 2 5 backplate temperature (deg c) xd1001-bd vd=5.0 v, id=160 ma 1 0 4 1 0 6 8 6 8 8 9 0 9 2 9 4 9 6 9 8 1 0 0 1 0 2 1 0 4 rth (deg c/w) 8 2 8 4 8 6 5 5 6 5 7 5 8 5 9 5 1 0 5 1 1 5 1 2 5 backplate temperature (deg c) xd1001-bd vd=5.0 v, id=160 ma 21 0 22 0 13 0 14 0 15 0 16 0 17 0 18 0 19 0 20 0 21 0 tch (deg c) 11 0 12 0 13 0 5 5 6 5 7 5 8 5 9 5 1 0 5 1 1 5 1 2 5 backplate temperature (deg c)
page 8 of 8 18.0-50.0 ghz gaas mmic distributed amplifier d1001-bd handling and assembly information part number for ordering description caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: do not ingest. do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. esd - gallium arsenide (gaas) devices are susceptible to electrostatic and mechanical damage. die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded antistatic workstation. devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. die attachment - gaas products from mimix broadband are 0.100 mm (0.004") thick and have vias through to the backside to enable grounding to the circuit. microstrip substrates should be brought as close to the die as possible. the mounting surface should be clean and flat. if using conductive epoxy, recommended epoxies are tanaka ts3332ld, die mat dm6030hk or dm6030hk-pt cured in a nitrogen atmosphere per manufacturer's cure schedule. apply epoxy sparingly to avoid getting any on to the top surface of the die. an epoxy fillet should be visible around the total die periphery. for additional information please see the mimix "epoxy specifications for bare die" application note. if eutectic mounting is preferred, then a fluxless gold-tin (ausn) preform, approximately 0.001 2 thick, placed between the die and the attachment surface should be used. a die bonder that utilizes a heated collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere is recommended. he gold-tin eutectic (80% au 20% sn) has a melting point of approximately 280 oc (note: gold germanium should be avoided). the work station temperature should be 310 oc +/- 10 oc. exposure to these extreme temperatures should be kept to minimum. the collet should be heated, and the die pre-heated to avoid excessive thermal shock. avoidance of air bridges and force impact are critical during placement. wire bonding - windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. the recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x 0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize rf port bond inductance. gold 0.025 mm (0.001") diameter wedge or ball bonds are acceptable for dc bias connections. aluminum wire should be avoided. thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. bond force, time and ultrasonics are all critical parameters. bonds should be made from the bond pads on the die to the package or substrate. all bonds should be as short as possible. xd1001-bd-000v rohs compliant die packed in vacuum release gel packs xd1001-bd-ev1 xd1001-bd evaluation module c a u t i o n : e s d s e n s i t i v e appropriate precautions in handling, packaging and testing devices must be observed. proper esd procedures should be followed when handling this device. january 2010 - rev 11-jan-10 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2010 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws.
|
